鋁板生產廠家

您的位置:首頁 > 新聞資訊 >

造成鋁板涂裝好壞的因素有哪些?

來源:http://www.fuzore.com  發布時間:2019-06-27 16:20:03  

  鍍膜是鋁板生產中的一項重要工藝。涂層的質量直接影響鋁板的裝飾效果。造成鋁板涂裝優劣的主要因素有四個,讓我們以下面的鋁板生產廠家來了解一下其中的內容。對這方面感興趣的朋友一定不要錯過。
  Coating is an important process in the production of aluminium sheet. The quality of coating directly affects the decorative effect of aluminium sheet. There are four main factors contributing to the quality of aluminium sheet coating. Let's look at the following aluminium sheet manufacturers. Friends who are interested in this aspect must not miss it.
  1.境
  1. territories
  涂裝內部要求清潔、防塵、防蟲、通風,保證鋁板涂裝的表面質量不受污染。同時由于溫度的變化和工藝條件的及時變化。
  The interior of the coating should be clean, dust-proof, insect-proof and ventilated to ensure that the surface quality of the aluminium plate coating is not polluted. At the same time, due to the change of temperature and process conditions in time.
  2.原材料
  2. Raw materials
  涂層和鋁是較因素可以影響涂料涂裝工藝的質量,由于涂料批顏色區別,涂料和涂層率不夠高,細度差涂料用溶劑、分層等將直接影響涂料和缺陷的鋁卷基材不均勻、膜厚度、不均勻偏轉的邊緣,也直接影響產品的質量和整體使用。因此,原材料的選擇應該嚴格控制。
  Coating and aluminium are the most important factors affecting the quality of coating process. Because of the difference of batch color, the paint and coating rate are not high enough. Solvents and layers used in poor fineness coatings will directly affect the non-uniformity of coating and defective aluminium coil substrate, film thickness, non-uniform deflection edge, and also directly affect the quality and overall use of products. Therefore, the selection of raw materials should be strictly controlled.

鋁板生產廠家
  3.備
  3. preparation
  涂裝線要求涂裝設備處于良好狀態,涂裝設備運行平穩,無水平和垂直抖動,涂裝輥磨細。涂布機各輥的水平跳動必須控制在允許范圍內,否則將嚴重影響涂布表面質量。
  The painting line requires the painting equipment to be in good condition, the painting equipment to run smoothly, without horizontal and vertical jitter, and the coating rollers to grind fine. Horizontal runout of each roll of coating machine must be controlled within the allowable range, otherwise it will seriously affect the surface quality of coating.
  4.工藝
  4. Technology
  涂裝工藝與涂裝質量密切相關,因此要求將涂裝輥、涂裝輥、測量輥與基體的相對線速度比控制在一定范圍內。根據不同的體系和涂層產品的薄膜厚度,將涂層設定一定的粘度范圍,以保證涂層光滑,促進產品質量的提高。涂料固化過程中,烘箱控制必須按照要求進行控制,不能隨意改變,否則會嚴重影響涂料產品的色差和性能。
  Coating process is closely related to the quality of coating, so it is necessary to control the relative linear velocity ratio of coating roll, coating roll, measuring roll and matrix within a certain range. According to the film thickness of different systems and coating products, the coating is set to a certain range of viscosity to ensure smooth coating and promote the improvement of product quality. In the curing process of coatings, oven control must be controlled according to the requirements, and can not be changed at will, otherwise it will seriously affect the color difference and performance of coatings products.
  以上內容是對鋁板生產廠家為您介紹的鋁板涂裝的優缺點的內容介紹,我相信無論是對這方面的了解還是對整個鋁板的了解都是有幫助的。http://www.fuzore.com
  The above content is an introduction to the advantages and disadvantages of aluminium coating introduced by aluminium plate manufacturers for you. I believe that both the understanding of this aspect and the understanding of the whole aluminium plate will be helpful. http://www.fuzore.com

国产欧美日韩精品a在线观看_欧美人与兽_被公侵犯玩弄漂亮人妻